本页主题: [砖头]dos下使用usb disk 打印 | 加为IE收藏 | 复制链接 | 收藏主题 | 上一主题 | 下一主题

galilette
级别: 嘉宾


精华: 30
发帖: 2139
威望: 1382 点
金钱: 0 静电币
支持度: 0 点
在线时间:3012(小时)
注册时间:2002-05-01
最后登录:2019-03-12

 [砖头]dos下使用usb disk

问题:有个朋友,本本是toshiba的portege 100, 超薄的那种,没有光驱,只有一个usb软驱和u盘一支。不知道玩什么不慎,搞得没法启动,要重装系统。

重装系统步骤:

    [*] 到 >>新dos时代<< 下载msdos "7.10" (呵呵,应该不是官方的东西)
    [*] 下载 >>mhairudos.zip (panasonic提供的通用usb设备驱动)<< , 将其中的usbaspi.sys, di1000dd.sys解压到比如c盘根目录。
    Quote:
    原文见 >> How to Recover Lost Partitions From External Hard Disk Drive <<
    let me mention that legalese on the Panasonic site most probably prevents you from downloading and using this driver on non-Panasonic devices, yet according to reports that are floating around on the Interweb, people have been able to use these "universal drivers" on a wide range of systems with different USB connectivity, UHCI, OHCI, and USB 2.0's EHCI with the NEC chipset.

    The Panasonic DOS drivers seem to work on most USB chipset implementations, including Intel and NEC, as well as NVidia, VIA, and SIS. It seems Panasonic engineers didn't want to have to write a driver every time for every different chipset, so they wrote this "universal" driver to work with all possible USB controllers.

    [*] 在config.sys中添加:
    Quote:

      device=c:\usbaspi.sys

      device=c:\di1000dd.sys

    [*] 重启,记得需要在系统启动前插上u盘。一般来说这样就可以使用u盘了,可以用来在台机和本本之间对考数据(备份文件,安装文件,etc)


建议:在这种无光无软的本本上应该留一个小分区(比如50M)给应急系统(legacy MS-DOS, FREEDOS 或者linux),并且配备必要的工具 (PQMagic, DM, HD-COPY, ghost, nc, ntfsdos, ...)

附mhairudos.zip
Posted: 2004-12-16 09:52 | [楼 主]
galilette
级别: 嘉宾


精华: 30
发帖: 2139
威望: 1382 点
金钱: 0 静电币
支持度: 0 点
在线时间:3012(小时)
注册时间:2002-05-01
最后登录:2019-03-12

 

追根溯源,找到这两个驱动的详细信息和最新版本,测试下来,性能上的确有很大提升。支持usb 2.0哦 (我的硬盘是通过ide-->usb2.0转接口接上的,速度仍旧很快)
原文请见: http://www.computing.net/dos/wwwboard/forum/15115.html

下面是全文转贴
Subject: USB DOS driver - USBASPI.SYS 2.xx

Original Message
Name: madmaxUSB (by madmaxUSB2)
Date: September 01, 2004 at 07:08:17 Pacific
Subject: USB DOS driver - USBASPI.SYS 2.xx
OS: DOS
CPU/Ram: Pentium/32
Comment:

  USBASPI.SYS Panasonic(TM) USB to ASPI driver v2.06 and v2.15 Reference
  Rev 4.2 updated 1 Sept, 2004 by madmaxUSB
  ===========
  For a brief history on how I got to research on this very useful driver, check out http://www.computing.net/dos/wwwboard/forum/13447.html
  ===========
  Most people will tell you MS-DOS does NOT support USB connected devices.

  This is somewhat true, because USB was developed way after Microsoft(TM) had opted to discontinue DOS.

  However, there are special device drivers that allow USB connected mass storage devices to be mapped as ASPI devices which can subsequently be accessed by DOS - much the same way as SCSI devices.

  This document provides useful information on using a specific device driver in getting USB 2.0 mass storage devices (like hard disks, flash memory, optical drives) recognized in DOS. It is provided for troubleshooting and reference purposes only.


  ===========
  Description:

  Version : 2.06 Version : 2.15
  File size : 37,903 bytes File size : 39,093 bytes
  Last modified : 27 Nov 2002 Last modified : 27 Oct 2003

  Support UHCI/OHCI/EHCI controllers and are compatible with many of the USB implementations from major chipset manufacturers like INTEL, VIA, NVIDIA, SiS and NEC for integrated, onboard, PCI bus or CardBus USB2.0 ports.

  These drivers seem to be based on work done by Novac Co. Ltd. and Medialogic Corp. hence they generally have similiar options and good interoperability.

  Your boot OS determines what kind of partitions will be supported in your USB device. For FAT32 support, use the DOS boot disk for Windows 98 (MS-DOS 7.10) or the Windows ME Emergency Boot Disk (MS-DOS 8.00). You can add support for long file names using special drivers. Check out these site for relevant links - http://www.opus.co.tt/dave/utils.htm

  There are other USB 2.0 DOS drivers released on the web, but were found to have a number of limitations in terms of compatibility and configuration:

  1. DATOptic's Speedzter supports USB 2.0 & Firewire - their DOS driver seems to be the next best driver in terms of compatibility and functionality.
  2. Cypress(TM) DUSE (ver 4.4 & 4.9) are a unified driver that also supports USB 2.0 and offer many options but seems to have issues for I/O port address or Memory address settings - particularly a limit on the address space range.
  3. Iomega(TM) USB & Firewire drivers also support USB2.0 (via ASPIEHCI.SYS) and is also used in Norton/Symantec GHOST but has limited compatibility.


  ===========
  Application:

  When used in conjunction with an ASPI Mass Storage Driver, it allows USB storage devices - particularly USB 2.0 hard disks or flash disks - to be accessible in DOS. This is particularly useful in drive cloning, partition resizing and image backup utlities that need to run in DOS mode (e.g. emergency disks for GHOST 2003, Partition Magic, etc...)

  Furthermore, with a USB CD-ROM Driver, it allows USB optical drives (DVD, CD-ROM) to be accessible in DOS when MSCDEX extensions are loaded. This makes it possible to install images or load Operating Systems onto newly formatted systems or replacement hard drives.

  Advantages over similiar drivers:
  1. Support for USB 2.0 as well as USB 1.1 (Other USBASPI.sys versions are actually for USB 1.1 only)
  2. Compatible with many USB chipset implementations, including Intel, NEC, VIA, NVidia and SIS
  3. Automatically obtains configuration parameters from Motherboard PnP/ PCI BIOS to minimize difficulties with I/O, Mem and IRQ mapping
  ======================================================================
  Please note that USB support in DOS is considered experimental!
  Most HW manufacturers DON'T provide support for their USB DOS drivers.
  ======================================================================

  There are three standards compliant controllers in PC's. In Windows, Go to ControlPanel - System and (look under Hardware or DeviceManager to) examine the listed devices under Universal Serial Bus Controllers to determine the type of USB ports detected:
  USB 1.x UHCI (Universal Host Controller Interface) Intel, VIA
  USB 1.x OHCI (Open Host Controller Interface) Compaq, Microsoft and National Semiconductor
  USB 2.x EHCI (Enhanced Host Controller Interface)

  USB 1.x is the initial standard. USB Support started in Windows95B and onwards. USB 1.1 supports a theoretical maximum transfer rate of up to 12 Mbps.

  USB 2.0 is the current standard and supports a maximum transfer rate of up to 480 Mbps.

  Since 2.0 is a superset of 1.1, some devices are marketed as USB 2.0 compatible but cannot operate at full speeds. Here is a table on the speed ratings:
  USB Type Code Max. Transfer Rate
  High-Speed HS 480 Mbps
  Full-speed FS 12 Mbps
  Low-speed LS 1.5 Mbps

  Actual I/O throughput with current USB 2.0 external hard disks is limited by processor interconnect type, protocol overhead and USB bus connections.
  Reportedly, for USB 2.0 ports integrated on system board chipsets, 25 MB/sec is the practical throughput, while add-on USB 2.0 PCI cards can give up to 16MB /sec only.

  Notes:
  1. For more reliable connections, avoid the use of USB hubs when connecting storage devices in DOS mode.
  2. The driver does NOT support hot-plug connections. Do not disconnect/reconnect USB devices after USBASPI.SYS has been loaded, until the syste, is powered OFF.


  ===========
  Recommended Usage:

  > To detect your USB Mass storage device (.e.g. a USB 2.0 external hard drive) put this line in your boot diskette CONFIG.SYS file

  device=USBASPI.SYS /w /v


  ===========
  USBASPI.SYS Switches:

  Here are the known valid switches identified so far with the Panasonic(TM) v2.xx USBASPI.SYS driver in CONFIG.SYS

  device=[{path}]USBASPI.SYS [/e] [/o] [/v] [/w] [/r] [/l[#]] [/p=xxx0] [/f] [/slow] [/nocbc] [/norst] [/noprt]

  You can specify more than one controller type (e.g. /e /u). This switch can also be used to force slower speed operation on high-speed USB controllers & devices.
  The driver will scan for all types of USB controllers, so use these switches to specify which port types to enable. This allows for faster USB scanning. By specifying /u or /o and omitting /e, it forces Full-Speed mode on High-Speed devices. Note that you can't make a Low- or Full-Speed device run at High-Speed.
  /e EHCI, for enabling only USB 2.0 controller
  /o OHCI, for enabling only add-on/onboard USB 1.1 controller
  /u UHCI, for enabling integrated USB 1.1 controller

  In verbose mode. USBASPI displays details on controller type and USB devices it detects. It displays the vendor & product ID codes, the controller address range (memory map or I/O port map) of controllers, and the connection speed code for each device.
  /v Verbose, shows USB details - excellent troubleshooting tool

  These switches modify driver actions
  /w Wait, displays prompt message to allow swapping/attaching of target USB device
  /l# Luns, to specify highest number of LUN assigned, default /L0
  /slow to enter SLOW down mode, gives longer delays when scanning USB devices
  /nocbc NO Card Bus Controller, to disable detection of USB on CardBus slots

  This switch is typically used on portable systems with an external USB floppy drive connected to the single USB port for boot-up. Used in conjunction with RAMFD.SYS so after the boot floppy is copied to a RAM drive, (and after the /W pause...) the USB floppy can be removed, and the target mass storage device can be attached and detected
  /r Resident, allows driver to stay resident in memory when USB floppy drive is detected.

  This switch is used to specify the UHCI I/O address. Use this if the PnP BIOS does not assign an I/O address, where xxx0 is in hexadecimal format.
  /p=xxx0

  There are a number of switches whose specific function is still unknown. Please post your discoveries in the USBMAN end-user forum, or the Computing.Net DOS forum.
  /noprt * Have found that on Intel systems (which have UHCI), using this switch causes the system to hang while detecting host controllers. Could it be related to I/O port?
  /norst
  /f

  Depending on the system processor, USB 2.0 host interface, USB bridge chip and actual harddisk specs, actual throughput may vary. The following were reported in DOS mode GHOST 2003 using Local -> Check -> Disk option:
  1. NEC based USB 2.0 PCI card - over 300 MB/min
  2. Intel chipset USB 2.0 onboard ports - over 500 MB/min
  Differences in transfer rate may be due to sharing of PCI bus bandwidth and protocol overhead (on USB and PCI busses) vs. direct connection of a similiar device to a PC.

  Note:

  In case the driver reports an error "Cannot set memory mode I/O" please disable Legacy USB device support in system BIOS setup.


  ===========
  Download Source:

  The USBASPI.SYS driver is supplied for portable USB 2.0 drives from Panasonic and available in the Japanese market. Follow any of the links below to the manufacturer's self-extracting drivers:

  USBASPI v2.06
  http://panasonic.co.jp/pcc/products/drive/cdrrw/kxlrw40an/driver/kxlrw40an.exe
  http://panasonic.co.jp/pcc/products/drive/cdrom/kxl840an/driver/kxl840an.exe
  http://panasonic.co.jp/pcc/products/drive/combi/kxlcb30an/driver/kxlcb30an.exe

  USBASPI v2.15
  http://panasonic.co.jp/pcc/products/drive/other/driver/f2h_usb.exe
  http://panasonic.co.jp/pcc/products/drive/combi/kxlcb35an/driver/kxlcb35an.exe

  They are listed here sorted from smallest to largest size. USBASPI.SYS is extracted from the F2H subdirectory

  These are from CD-R/RW, CD-ROM and DVD+CD-R/RW products intended for the Japanese market, but work OK in English version DOS & Windows.

  Observed differences between the two driver versions:
  1. Unlike v2.06, the newer v2.15 does not unload from memory if it does not find a USB mass storage device, consuming about 14KB in DOS. (-)
  2. V2.15 seems to be able to initialize and scan for USB controllers, hosts and devices faster than v2.06. (+)
  3. Performance is reported to be slightly better in v2.15 vs v2.06. (+)
  4. However, v2.06 provides a much more informative verbose mode than v2.15 as you can tell where each USB1.x device is logically connected to. (-)

  Keep these in mind when choosing which driver to use in your DOS environment.


  ===========
  Other Useful Files:

  Here are some useful device drivers that complement USBASPI.SYS:


  From the same Panasonic driver file you downloaded to get USBASPI.SYS, in the F2H subdirectory are 2 other important drivers
  USBCD.SYS v1.00 from Panasonic, USB CD-ROM device driver
  RAMFD.SYS v1.01 or v1.02 from Panasonic, copies boot floppy disk contents into a RAM disk, write protects it, and remaps the floppy drive letter to the RAM disk.


  As USBASPI.SYS merely maps USB devices to an ASPI device, additional driver is needed to map the ASPI mass storage to a DOS drive letter. The famous "Motto Hairu" driver includes this important piece, and can be downloaded from:
  http://www.driver.novac.co.jp/driver/hd352u/hd352u_dos.zip

  [Note: If this link doesn't work, start at http://www.driver.novac.co.jp/driver/hd352u/hd352u_drv.html]

  UnZip the file to get these files (the latter has an english translation readme file)

  DI1000DD.SYS v2.00 from Novac, ASPI Mass Storage Device Driver {reportedly drive needs to be ATA66 or faster)

  ======================================================================
  DI1000DD.SYS
  ASPI Disk Driver v2.00 from Novac Co., Ltd

  device=[{path}]DI1000DD.SYS [/hN] [/dL]

  If USBASPI.SYS detects multiple mass storage devices on multiple host adapters, use
  /hN Host, to specify which host adapter to map drive letter(s), where N would be the 3rd number set reported for the USB controller in USBASPI.SYS with the /v switch.

  To specify the starting drive letter for detected mass storage devices, use
  /dL Drive_letter, where L is the first assigned letter for this host adapter

  Example of use:

  If you want specify the "L" drive letter for a storage
  device, try:

  device[high]=[{path}]di1000dd.sys /dL

  Thanks to Daniel G. Gionco for this useful bit of information :-)
  ======================================================================


  In case you have compatibility problems, there are some similiar drivers here

  http://www.datoptic.com/Drivers/DAT.exe

  This image file creates a bootable diskette that supports USB and firewire in DOS. Of relevance are these drivers:
  USBASPI.SYS v2.01 from Medialogic Corp, is very similiar but less-featured version than Panasonic's USBASPI.SYS.
  NJ32DISK.SYS v1.06 from Workbit Corp. is very similar to Novac's DI1000DD.SYS.
  SBP2ASPI.SYS v1.02 from Medialogic Corp provides ASPI mapping of Firewire storage devices.


  ===========
  Examples:


  > If the USB devices are already plugged upon power up and you want to enable only the high-speed USB controller and external hard disk drives, try

  device=USBASPI.SYS /e /v
  device=DI1000DD.SYS


  > If you have only a single USB port and no internal floppy, use this CONFIG.SYS combination:

  device=RAMFD.SYS
  device=USBASPI.SYS /w /v /r


  > If you have a notebook with a USB optical drive, install the ASPI CD-ROM device driver after loading USBASPI.SYS in CONFIG.SYS like this:

  device=USBASPI.SYS /w
  device=USBCD.SYS /d:USBCD001

  and in AUTOEXEC.BAT:

  MSCDEX /d:USBCD001


  > If you want to connect a USB 2.0 optical drive and a USB 2.0 external hard disk simultaneously, put these in the CONFIG.SYS file:

  device=USBASPI.SYS /e /w
  device=USBCD.SYS /d:USBCD001
  device=DI1000DD.SYS

  and in AUTOEXEC.BAT:

  MSCDEX /d:USBCD001

  > For troubleshooting USB connections, install all your devices and boot from your diskette with this in CONFIG.SYS:

  device=USBASPI.SYS /v


  ===========
  Troubleshooting Info:

  With the /v option, USBASPI.SYS provides a lot of useful info regarding the USB devices connected to a PC.

  Use this info to determine if a problem is in the hardware level, or a Windows driver/configuration issue.

  Example result for v2.06:

  Controller : 00-09-0 VID=1033h PID=0035h (3782h-0035h) OHCI
  : MEM=DF000000h-DF000FFFh(4KBytes)
  Controller : 00-09-1 VID=1033h PID=0035h (3782h-0035h) OHCI
  : MEM=DE800000h-DE800FFFh(4KBytes)
  Controller : 00-09-2 VID=1033h PID=00E0h (3782h-01E0h) EHCI
  : MEM=DE000000h-DE0000FFh(256Bytes)
  USB Device : HOST [00-09-2 VID=1033h PID=00E0h (3782h-01E0h) EHCI]
  : |-- VID=05ABh PID=0060h HS
  : |-- VID=05E3h PID=0702h HS
  : ^-- 2 device(s)
  USB Device : HOST [00-09-0 VID=1033h PID=0035h (3782h-0035h) OHCI]
  : ^-- nothing
  USB Device : HOST [00-09-1 VID=1033h PID=0035h (3782h-0035h) OHCI]
  : |-- VID=066Fh PID=4200h FS
  : ^-- nothing
  ASPI Device : ID:0 LUN:0 = IC25N010 ATDA04-0 0811
  : ID:1 LUN:0 = E-IDE CD-ROM 48X/AKU T3A

  Example result for v2.15:

  Controller : 00-09-0 VID=1033h PID=0035h (3782h-0035h) OHCI
  : MEM=DF000000h-DF000FFFh(4KBytes)
  Controller : 00-09-1 VID=1033h PID=0035h (3782h-0035h) OHCI
  : MEM=DE800000h-DE800FFFh(4KBytes)
  Controller : 00-09-2 VID=1033h PID=00E0h (3782h-01E0h) EHCI
  : MEM=DE000000h-DE0000FFh(256Bytes)
  USB Device : VID=05ABh PID=0060h HS
  : VID=05E3h PID=0702h HS
  : VID=066Fh PID=4200h FS
  ASPI Device : ID:0 LUN:0 = IC25N010 ATDA04-0 0811
  : ID:1 LUN:0 = E-IDE CD-ROM 48X/AKU T3A

  Interpretation:
  1. There are 2 OHCI and 1 EHCI controllers detected. All are running in MEMory map mode (not I/O mapped) with the respective address spaces displayed.
  2. Two devices are mapped to the EHCI controller. The HS indicates they are running at High Speed.
  3. One device is mapped to the 2nd OHCI controller. The FS indicates runs at Full Speed only. ^-- nothing indicates no USB storage devices were found.
  4. Two of the devices connected are detected as storage devices. Each is mapped to an ASPI ID, and it's identifier is displayed.
  5. This config has an IBM 10GB notebook HD & a 48x EIDE CD-ROM drive.

  Notes:
  1. The respective USB bridge/device can be identified by referring to the 2-byte Vendor ID and Product ID.
  2. Most of the configuration is automatically obtained from BIOS PnP info. Unfortunately, USBASPI.SYS does not identify IRQ's used.


  ===========
  On the still unknown switches:

  /norst - could this mean a RESET will not be sent on the USB device? what is the effect? have tried on a USB printer but saw no difference ...

  /f - does NOT seem to be speed related (as in full-speed or fast device detection). Suspect it could be for "floppy" or "flash memory" devices ...

  /m=xx - in the older USBASPI.SYS v1.xx, is used to specify the OHCI memory map address but does NOT deem to work for v2.xx

  ===========
  Thank you to members of DarkeHorse, Computing.NET and USBMAN forums for sharing their experiences.


  ===========
  * All brands mentioned are TM of respective owners. Many products mentioned are (C) and require an appropriate end-user license. *
Posted: 2004-12-17 03:55 | 1 楼
帖子浏览记录 版块浏览记录
狗狗静电BBS - wwW.DoGGiEhoMe.CoM » 电脑全方位 Computer Guide

沪ICP备05008186号
Powered by PHPWind Styled by MagiColor